Scroggins will enhance the efficiency of your cannabis plants and maximize yields. There’s an art of bringing together a group of plants and spacing out their limbs so that they don’t expand or shadow each other but we’re trying to demystify the process. Bear in mind that each plant is distinct and there is no precise calculation of how similar each plant or branch can be or how far away. Scroggins requires reading a plant to see what it needs and some fine-tuning is normally involved. Stick with us until the end until you will learn about how to scrog by the yield of marijuana.

Yet your plants are going to be safe and green with a little time and practice. If you know any producers of marijuana, you’ve definitely used the word “SCROG” before. Scroggins pot, like many rising approaches, strives to make the operation a bit simpler and a lot more beneficial. Better delivery of light helps achieve greater yields, For a bit, the scroggin technique has been around. It has been used by people long before high-intensity discharge-HID-lamps. Even with simple fluorescent lights, this will increase the yield of your growth.

 Is it crucial to Scrog cannabis plants?

First, to reveal more nodes to direct light, it spreads out branches, thereby increasing the yield. Stretching branches out over a plant increases the airflow, helping to avoid bud rot. A scrog provides branch protection so that they do not flop over or split as buds grow bigger. Thick buds will cover all the trees above the screen and much of the vegetation below the screen will be shaded. You ought to prune these dead leaves and bottom branches so they either will not produce buds or subpar buds will be produced. If you can divert energy from those branches to the quality buds above the screen, you’ll get the most out of your plant.

Spacing and Positioning

Select a collection of plants, preferably of the same height and scale, to begin with. Scroggins plants of varying sizes are difficult since the panel has to be level across the entire canopy in order to disperse light equally.” Nylon screens come in various sizes of mesh, usually 4-6″ square. Try a 4′ mesh for smaller growth. It is important to position plants so that they are not cramped, but not so far apart that there are wide gaps in the canopy. When they are pulled up by the scrog, you want some space between plant branches. Plants can always expand and fill in a little bit so they have at least eight weeks to go through the flowering period.

Try placing 19 to 21 plants in 5-gallon containers as a rule for a 4 x 8′ plate. That will help you obtain rows of six or eight plants, and you should have a sense of how many plants are going to match together. Depending on the tray and pot size, you should change accordingly.

It will benefit to fold the branches back a bit to get them ready for the screen once all the plants are in place. During this phase, be extremely careful! Snapping the branches is convenient.

Fold leaves, like a flower opening up or peeling a banana, out and away from the main stem. Bear in mind, too, that some strains are harder and can handle more stretching than others.

The Panel Stretching 

To bring the computer on, you’ll need at least four points of touch. Many farmers can use a vertical extension at each end of the canopy that can sustain any impact, like a two-by-four or a T-post.On one post at a time, position each corner of the frame, extending the screen as you go. Place the screen quite loosely on all four touchpoints and clamp it down later.

Shimmy it off after the screen is on until it was on top of the trees. Preferably, you also want the screen approximately 6-9′ just above plants’ minimum budding, which is the first topping you give the crop and the first point at which plant begins to branch just after the stem rises out from the dirt.

Make sure it’s secure, particularly the edges, when the screen is set the tighter it is, the better it is able to keep the shape and hold the weight of buds that are forming. Zip connections here come in handy. To tighten it up, you can take a portion of the panel and drag it back, and zip it to a post. Each point should be tightened by about the same amount so that the screen is not lopsided. Be alert, as it might crack, not to draw the screen too close.

Placing Branches

The branches on the screen would interlock with the branches of all the other plants surrounding it at the end of the day. Think about opening your hands and putting one hand’s fingers in between your other hand’s fingers. Before placing branches in the scrog, an important question to consider is Where does the branch want to go? You may need to position it anywhere else if a branch doesn’t want to continue where you put it. Do not push this.

Try to fill a single branch for each square mesh of the screen; stop placing two branches in one square and try not to leave a square vacant. This would ensure that enough room and light is provided to each branch and that the screen is used to its fullest capacity. Depending on how much plant material you have, you will not be able to do these, but they are useful guides to follow. For each squared grid of its screen, try to fill a single branch; stop putting two branches in one area but try to not leave a space blank.

For each squared grid of its screen, try and fill a single branch; stop putting two branches in one area but try to not leave a space blank. A corner, at one of the posts, is a good place to start on the scrog. Work your way towards the next pillar along with one of the sides, and do another edge until both edges are covered in then work on the center. Act methodically, before going on to the next plant, bringing the branches of one plant into the screen.

Maintenance

Scroggins will stress out a plant, extending across all its branches. You would probably find that after doing so, your plants look a little wilty, or like they “took a hit”. But fear not in any direct illumination, they will bounce back, and it will be worth it, in the long run, to bring them through the scrog. A lovely canopy of buds will grow and fill in above the screen. But because the foliage gets dense with buds, everything would get shaded out under the screen and most likely die.

Cleaning up dead leaves and pruning small branches that do not receive light under the screen is necessary. Branches will start to grow buds, but your time and effort won’t be worth it. It is easier to get rid of them and make the plant redirect energy, making them better and more colorful, to the buds above the screen.

READ  Top 10 Premium Marijuana Strains You Can Grow Outdoor